HW-CM36
The HW-CM36 is a single-module 360-degree camera for operated equipment such as forklifts, ground support equipment, and other slow-moving off-road assets. The camera connects to a Vehicle Gateway through USB and provides full surround visibility for backing, turning, docking, and other tight maneuvers.
Complete Vehicle Gateway Installation and camera activation before you mount the CM36.
The following items are included with the CM36. Gather any additional hardware and tools before you start.
|
Item |
Quantity |
Description |
|---|---|---|
|
|
1 |
CM36 360 camera with integrated USB cable |
|
|
1 |
CM36 mounting bracket with 1/4-20 in mounting screw |
|
|
1 |
Vehicle Gateway (sold separately) |
|
|
1 |
3 mm hex wrench |
|
|
1 |
Cable clips |
|
|
4 |
M4.2 self-drilling screws (7 mm head) |
|
|
2 |
Cable ties (CM36 box) |
|
Sold separately |
||
|
1 |
Diagnostic cable (varies by equipment) |
|
|
Optional hardware |
||
|
As needed |
Heavy-duty CM36 bracket; recommended for yellow iron, belt loaders, and other exposed mounting locations |
|
Before you mount the camera, gather the necessary equipment and tools. If a dash cam is already installed on the asset, remove the existing equipment or follow Remove an Installed Dash Cam.
To ensure the camera captures video on slow-moving or frequently stationary equipment, install the Vehicle Gateway with a diagnostics-enabled cable that provides constant power. If diagnostics are unavailable, connect an AUX pin to an ignition source using CBL-VG-CAUX and label it as Equipment Activity, and connect Vehicle Gateway power to a constant battery power source. For best results, set the asset type to Equipment (rather than Vehicle) in the Vehicle Gateway settings.
Note
The Vehicle Gateway must run firmware version 37 or higher for CM36 compatibility. New-in-box gateways may ship on earlier firmware. Connect the gateway to power and allow time for an over-the-air update before you connect the CM36.
-
Before you begin:
-
Gather the necessary equipment and tools.
-
Install and activate the Vehicle Gateway.
To capture video on slow-moving or frequently stationary equipment, install the gateway with constant power and an equipment activity signal.
Activate the VG using the guided instructions in the Samsara Fleet App, or go to the activation page at the regional Samsara cloud URL assigned to your organization (such as cloud.samsara.com/activate, cloud.ca.samsara.com/activate, or cloud.eu.samsara.com/activate).
-
Activate the CM36 using one of the above activation methods.
-
-
Identify a mounting location.
Position the camera so the side with the button faces the driver for easy access and optimal driver visibility. The camera records a 360-degree field of view and can be installed in any orientation. After installation, you can adjust the recorded orientation on the CM36 device in the Samsara dashboard to match the physical mount.
Physical Mount
Rotation Value
0° (default horizontal)
0
90° clockwise
1
180°
2
270° clockwise
3
Apply the config override on the CM36 device, not the VG, when the mount rotation is not 0. No config override is needed for rotation 0.
-
Mount the camera bracket using your preferred method.
The camera can be attached using one of the following methods:
-
Self-tapping screws (#8, #10, M3.9, M4.2, or M4.8)
-
Bolts and nuts (#8, #10, M4, or M5)
-
Rivets
-
Zip ties
-
Hose clamps (5/16 in max width)
-
VHB
Note
If you use VHB, thoroughly clean the mounting surface and any areas where you plan to install adhesive-backed cable clips. Use the included alcohol wipe to remove any residual cleaner residue and allow the surface to dry completely. Install the camera only when temperatures are above 50°F (10°C). In colder conditions, use the vehicle windshield defroster or a heat gun to help the adhesive bond effectively for a secure installation.
Tip
For yellow iron, belt loaders, and other exposed mounting locations, use a heavy-duty CM36 bracket instead of the included plastic bracket.
-
-
Position the camera on the bracket.
For best performance, face the driver-facing camera directly toward the driver. The camera field of view is 360 degrees.
-
Route the cable to the Vehicle Gateway.
Use the included cable clips or cable ties to run the cable away from moving parts and sharp edges. Confirm that the cable does not interfere with any vehicle safety systems.
-
Plug the camera into a USB port on the Vehicle Gateway.
-
Complete the installation in the Samsara dashboard or Samsara Fleet App.
Turn the equipment on. Verify camera visibility using the Take Picture workflow in the Samsara dashboard or Samsara Fleet App.
If all points of interest are not captured, use the included 3 mm hex wrench to loosen the camera and readjust the angle.
This installation guide contains typical information specific to products manufactured at the time of its publication. The contents of this guide do not constitute a warranty and are for reference only. Consult applicable local laws and ordinances to determine any installation restrictions. It is the installer's responsibility to comply with all applicable laws and ordinances and rights to privacy when installing this hardware.
Do not attempt to repair this product, use any third party replacement parts with this product, or otherwise modify this product except in accordance with product manuals or as otherwise instructed by Samsara. Failure to do so may cause property damage, lead to physical injury, or void your product warranty.
Any installation not in accordance with the instructions in the installation guide or otherwise in the Documentation or use of this product other than as described by the relevant IP rating or recommended operating conditions may result in unexpected downtime, system failure, physical injury or property damage, including water damage. Failure to follow these directions could result in serious injury or death.
This hardware and any associated software may not be compatible with third party products and/or services and may interfere with the operations of or void warranties for such third party products and/or services.
Do not install or adjust hardware while driving or operating the vehicle. Do not install this hardware in a location that could interfere with the driver's visibility or operation of vehicle controls. Do not install this hardware on or near airbag panels or within the working range of an airbag. Do not install hardware while the vehicle is unsecured. Do not install hardware while the vehicle is turned on unless instructed to turn on the vehicle by the installation guide.
Do not install this hardware on or near flammable or otherwise hazardous materials. This hardware may burst if placed near flammable or other hazardous materials, creating a risk of fire, burn, shock, or other serious injury.
This product includes capacitors, which may present a potential fire, explosion, electric shock, or burn hazard. Do not touch or come into close proximity to any capacitors within this hardware.
Please always pay attention to your surroundings and drive safely, comply with all traffic laws, and observe the road and driving conditions at all times. Do not rely on the product to alert the driver of safety hazards or to prevent collisions. The hardware and associated software may not work as intended depending on road conditions, other vehicles, weather, and other factors.
Keep this hardware between -40°F and 140°F (-40°C and 60°C). Failure to keep this hardware in the specified temperature range may result in safety risks.
Failure to follow mounting instructions may create risk of physical injury or property damage from falling objects. If mounting the hardware to a building wall, check for wiring or plumbing before drilling any holes.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device complies with ISED Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
|
|
This symbol on the product(s) and / or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take this product(s) to designated collection points where it will be accepted free of charge. |
Comments
0 comments
Article is closed for comments.