Install Bird's Eye View fisheye cameras (HW-MC41) and a supported monitor for multi-camera feeds on the AI Multicam Hub (HW-MC-AIM4) using threaded GX12 connectors. This guide covers placing and mounting the four fisheye cameras and calibrating the system on a vehicle that already has the Vehicle Gateway, AI dash cam, and AI Multicam Hub installed.
For product features, see Bird's Eye View Overview. For dashboard configuration of detections and proximity zones, see Configure Bird's Eye View Settings. For recommended camera positions by vehicle type, see Bird's Eye View Vehicle Placement Options.
Note
Bird's Eye View is a driver aid. It does not replace mirrors, walk-around checks, or safe and attentive driving, and it may not detect every person or object. Performance depends on correct installation and calibration, and on conditions such as weather, lighting, and obstructions.
To install and calibrate Bird's Eye View, follow this sequence:
Complete these checks before you place cameras or run calibration. Confirm licenses, app access, prerequisite hardware, equipment, install location, and placement guidance so the install can proceed without rework.
-
Licenses: Confirm the vehicle has a Bird's Eye View license (LIC-BEV) on the fleet's Samsara account.
-
App and dashboard access: Update the Samsara Fleet App and confirm that you can sign in as an admin or installer.
-
Install prerequisite Samsara hardware: Complete the AI Multicam Hub Installation Guide first, including Vehicle Gateway, dash cam, hub, and trigger wire installation when applicable, before you install the four fisheye cameras.
-
Equipment and tools: Gather the Samsara equipment, tools, fasteners, and consumables listed in What You'll Need.
-
Monitor: Install a supported in-cab monitor so you can verify camera feeds before calibration. See 10-Inch Monitor for Multi-Cam (HW-MN12) or 7-Inch Monitor for Multi-Camera (HW-MN11).
-
Install location: Choose a flat, level, evenly lit area with 10–15 ft (3–4.5 m) clear on every side. Indoors is best. Cell or internet connectivity is required.
-
Camera placement: Review Bird's Eye View Vehicle Placement Options for recommended positions by vehicle type before you plan mounts.
Gather the following equipment and tools before you start.
|
Item |
Part Number |
Qty |
|---|---|---|
|
Vehicle Gateway |
HW-VG54 or HW-VG55 |
1 |
|
AI Dash Cam |
HW-CM33 or HW-CM34 |
1 |
|
AI Multicam Hub |
HW-MC-AIM4 |
1 |
|
Fisheye camera |
HW-MC41 |
4 |
|
[Optional] Fisheye camera mounting brackets |
ACC-MC41-TILT, ACC-MC41-CLMP |
As needed |
|
In-cab monitor, 7" or 10" |
HW-MC11 (7") or HW-MC12 (10") |
1 |
|
Camera extension cables |
CBL-MC-GX5 (5 m / 16 ft), CBL-MC-GX10 (10 m / 32 ft), or CBL-MC-GX15 (15 m / 50 ft) |
As needed |
|
Calibration mats |
ACC-BEV-AMAT |
1 set |
|
Component |
Tools and Fasteners |
|---|---|
|
Fisheye camera (HW-MC41) |
|
|
90° tilt bracket (optional) |
|
|
Band clamp bracket (optional) |
|
|
In-cab monitor, 7" or 10" (HW-MC11 or HW-MC12) |
|
These tools are not included with the kit:
-
Ladder or lift
-
Metric hex key set (include M2.5 for camera angle adjustment)
-
Tape measure
-
Wheel chocks
Every installation follows the same basic layout. Mount one camera near the center of each side of the vehicle, then place four calibration mats, starting ~5 ft off each corner. Each camera needs to see the two mats to its left and right. Adjust the mat and camera positions as needed if a camera can’t see them.
Note
The system will accept some variation in mounting position and camera placement. The recommendations provided in this guide are best practices.
Choose an installation path, then follow the shared camera placement, mat, and hub-port rules that apply to every Bird's Eye View install. Use Bird's Eye View Vehicle Placement Options for vehicle-specific placement guidance.
-
Established camera placement: Use for vehicles such as box trucks and vans when placement is well understood or follows Bird's Eye View Vehicle Placement Options. Complete Plan Camera Placement and Mounting, skip Test Fit and Verify Placement, then complete Mount, Route, and Connect the Cameras and the Calibration steps.
-
Uncertain camera placement: Use when you are installing on a new asset type or when recommended placements may not suit the vehicle. Complete all Camera Installation topics, including the optional test fit and test calibration, then complete Calibration.
Mount one camera near the center of each side of the vehicle. Place four calibration mats about 5 ft (1.5 m) off each corner.
Each camera must see the two mats to its left and right, with no obstructions, before you calibrate. You can adjust mat placement as needed.
Before you drill or permanently mount, confirm that each camera can see two calibration mats on its side plus a small portion of the vehicle edge. Use Bird's Eye View Vehicle Placement Options as a starting point.
|
Guideline |
What It Means |
Flexibility |
||
|---|---|---|---|---|
|
Mount near the midpoint of each side of the vehicle. |
When possible, mount near the midpoint. Off-center is fine to clear doors, ladders, or mirrors, but far off-center install increases image distortion. |
Flexible |
||
|
On the outermost surface |
Install front cameras at the furthest forward point on the vehicle for optimal AI performance. Mount left and right cameras at the same height and the same distance from the front of the vehicle. When possible, mount each camera where it has a clear view of the ground directly below it. Side cameras should mount at the widest part of the body. NoteSome vehicles, particularly operated equipment, have implements such as buckets or tracks that interfere with the view. This is sometimes unavoidable. |
Strict |
||
|
Mounting height |
Before you use permanent fasteners, temporarily mount cameras with adhesive or magnets to confirm height, angle, and field of view. Mounting height varies by vehicle. For optimal calibration and AI detection, keep camera height below 12 ft (3.7 m) off the ground and high enough (about 60 in [152 cm]) so each camera can clearly see two of the four calibration mats on its side of the vehicle. Lower installs are common and still largely successful, but objects and people stretch and distort more in the image. |
Flexible |
||
|
Parallel with the vehicle edge |
Mount the camera parallel to the vehicle edge. Significant rotation in the yaw axis can affect calibration. |
Strict |
||
|
Parallel with the ground |
Mount the camera roughly parallel to the ground, and minimize rotation in the roll axis. Viewed from head on, the camera should not be turned clockwise or counterclockwise. |
Strict |
||
|
See the vehicle edge in the camera view |
Tilt the camera downward until the vehicle's edge fills the bottom 10–15% of the view. |
Flexible |
Temporarily mount cameras and run a test calibration before permanent installation when placement is uncertain.
-
Remove the plastic cover from each fisheye camera.
Uninstall the three snap fits. Unclip the two snaps on the front with a flathead screwdriver, then pull the cover backward to release the hidden snap at the back.
Note
Do not reinstall camera covers until placement is final and all adjustments have been made. Removing covers after permanent mounting is very difficult.
-
Lay out the calibration mats.
Park on flat ground and place a mat at each corner, approximately 5 ft (1.5 m) out and square to the vehicle.
-
Connect the cameras.
Plug cameras into the AI Multicam Hub in this port order: 1 Left, 2 Right, 3 Rear, 4 Front. Port 1 is next to the power cable.
-
Temporarily mount each camera to evaluate placement.
Use magnets, VHB, or duct tape for the test fit.
Confirm that no obstructions block the camera view. Each camera should show the ground directly below the vehicle face and a clear view of two calibration mats.
-
Adjust camera tilt if needed.
Loosen the screw on each side of the camera with an M2.5 Allen key. After you set the desired angle, tighten both screws to lock orientation.
-
Verify mat visibility before calibration.
Before you run calibration, confirm that each camera can see two of the four mats in its field of view.
-
Run a test calibration.
Follow the calibration steps through Check the preview, but do not tap Finish calibration yet if you still need to permanently mount the cameras.
Note
If calibration fails, confirm that each camera sees two mats with no obstructions, mats are not too close or too far from the vehicle, camera height is sufficient, and lighting is adequate for the mats to be visible in each feed.
Permanently mount each camera using the option you chose in Plan Camera Placement and Mounting. Most installs use the camera's built-in mount. When the body prevents direct mounting, use a 90° tilt bracket or band clamp bracket.
|
Built-in camera mount (no bracket) |
90° tilt bracket, ACC-MC41-TILT |
Band clamp bracket, ACC-MC41-CLMP |
-
Position the vehicle and lay out the mats.
Skip this if the mats are still in place from Test Fit and Verify Placement (Optional). Park on flat, level ground. Fold in mirrors and move any implements (crane, boom, bucket) that would block a camera's view of a mat. Place a mat flat at each corner, about 5 ft (1.5 m) out and square to the vehicle, unless Bird's Eye View Vehicle Placement Options says otherwise. The mats are interchangeable and can face any direction.
-
Prepare to drill.
Disconnect the vehicle battery. Check behind each drilling position for wires, hoses, and reinforcing plates, and on cab and van roofs, for curtain airbags.
Note
Never drill into a vehicle's rollover or falling-object protection (ROPS/FOPS) structure without approval. Use a band clamp bracket instead.
-
Mount each camera using the mount option you chose in Plan Camera Placement and Mounting:
-
Built-in mount
-
Mark the four screw holes and the cable pass-through.
-
Drill a 3/4 in (19 mm) pass-through hole and 1/8 in (3.2 mm) pilot holes.
-
Feed the cable through the hole, install the grommet, then pull the cable through until the camera seats.
-
With the rubber gasket against the body, check for clearance behind the panel, then fasten the camera with four M4 self-tapping screws.
-
-
90° tilt bracket
-
Attach the camera to the bracket with four M4 machine screws.
-
Mark the base plate holes and fasten the base to the vehicle with at least two M6 (1/4 in) self-drilling screws. Leave the lock nut loose.
-
Set the angle, then tighten the lock nut.
-
-
Band clamp bracket
-
Attach the camera to the bracket with four M4 machine screws.
-
Thread a band clamp through each relief jog on the bracket.
-
Clean the pole where the clamps will sit. To protect the pole and keep the clamps from slipping, wrap self-fusing silicone tape or VHB under each clamp.
-
Position the camera and tighten the clamps evenly.
-
-
-
Route and secure the cables.
Route the extension cables to the AI Multicam Hub. Secure them with zip ties along the way, clear of pedals, steering linkage, and moving parts.
-
Connect the cameras to their hub ports: 1 Left, 2 Right, 3 Rear, 4 Front.
The port sets each camera's side and can't be changed in the app.
Tip
Label each cable end with a strip of tape to make it easy to determine which camera it corresponds to.
-
Reconnect the battery and check the views.
Turn the ignition on and confirm each view shows the correct side. If one doesn't, turn the ignition off and move that cable to the right port. If you skipped Test Fit and Verify Placement, adjust each camera's tilt now so the vehicle's edge fills the bottom 10–15% of the view.
-
Tighten everything well.
Tighten the angle screws, any tilt bracket lock nuts, and any band clamps.
Important
Make sure every camera is fully secure before you calibrate. If a camera moves, the calibration will be off.
Calibration stitches four camera views into one top-down view. Run calibration at installation, or again if you replace or move a camera or the hub.
Before you start the app, confirm the following:
-
Vehicle: Parked in the calibration position, parking brake on, wheels chocked.
-
Engine: Running (ignition alone is not enough) through Calibrate in the Samsara Fleet App. Ensure ventilation if you are indoors.
-
Monitor: Shows four camera views (or Bird's Eye View for a recalibration).
-
Mats: Flat, unobstructed, with no harsh shadows or glare.
-
Area: Everyone clear of the space between the vehicle and the mats.
-
Connection: Strong phone internet; vehicle online in the Samsara Fleet App.
-
Start the installation.
In the Samsara Fleet App, select the vehicle and start the AI Multicam installation.
-
Select Bird's Eye View.
Select AI Multicam (AIM4). For Is this a Birdseye Install?, choose Yes, then tap Begin installation.
-
Confirm the camera ports.
The app shows the proper wiring order for the cameras: 1 Left, 2 Right, 3 Rear, 4 Front. Confirm that each camera is connected to the matching port on the AI Multicam Hub, then tap Next. If a camera is in the wrong port, move the cable to the correct port.
-
Complete any required trigger-wire confirmation screens, then continue to mat placement.
-
Take photos.
Tap Take photos. The app captures a still image from each camera. Keep cameras and mats still.
-
Review the camera views.
-
Swipe through the four photos, or tap a thumbnail.
-
Orientation: Ensure the vehicle edge is at the bottom of the frame. If it is at the top, tap Flip.
-
Mats: Ensure both mats are fully visible, inside the dashed outline, and unobstructed. If not, move the mats, tap Retake photos, and recheck all four views.
-
-
When all four views pass, tap Calibrate Birdseye View.
-
-
Wait for calibration.
Calibration can take up to 10 minutes. Keep the engine running and the app open with the screen on until it finishes.
-
Check the preview.
On the Calibration complete screen, confirm the following:
-
Ground around the vehicle is visible with no large blind spots.
-
Stitched views are aligned. Calibration mats appear once in each corner with sharp patterns and little distortion or ghosting.
-
The vehicle outline is a clean rectangle. For equipment such as loaders or excavators, tap Adjust vehicle boundary to hide artifacts such as buckets or booms.
Distortion at the edges and stretching of tall objects is normal. If the result looks off, move the mats slightly and recalibrate, or see Troubleshooting.
-
-
Finish calibration.
Tap Finish calibration. The monitor switches from four camera views to Bird's Eye View, with individual views available to the right. A Samsara admin can adjust these views in the Samsara dashboard.
Note
The monitor may take up to 15 minutes to update with the Bird's Eye View.
-
Do a final check.
-
Walk-around: Have someone watch the monitor while walking around the vehicle to check for blind spots.
-
If the vehicle has triggers wired: Shift into reverse to confirm the focus view switches to the rear camera, and activate the left and right turn signals to confirm the focus view switches.
-
-
Reinstall camera covers and verify the system.
After successful final calibration, reinstall camera covers. Start the vehicle and confirm monitor power, video streams, and Bird's Eye View on the monitor.
-
Installation complete.
This installation guide contains typical information specific to products manufactured at the time of its publication. The contents of this guide do not constitute a warranty and are for reference only. Consult applicable local laws and ordinances to determine any installation restrictions. It is the installer's responsibility to comply with all applicable laws, and ordinances and rights to privacy in your jurisdiction when installing this hardware.
Do not attempt to repair this product, use any third-party replacement parts with this product, or open or otherwise modify this product, except in accordance with product manuals or as otherwise instructed by Samsara. Failure to do so may cause property damage, lead to physical injury, or void your product warranty.
Any installation not in accordance with the instructions in the installation guide or otherwise in the Documentation or use of this product other than as described by the relevant IP rating or recommended operating conditions may result in unexpected downtime, system failure, physical injury or property damage, including water damage. Failure to follow these directions could result in serious injury or death.
This hardware and any associated software may not be compatible with third-party products and/or services and may interfere with the operations of or void warranties for such third-party products and/or services.
Do not install hardware while the vehicle is unsecured or while the vehicle is turned on unless instructed to turn on the vehicle by the installation guide. Do not install or adjust hardware while driving or operating the vehicle. Do not install this hardware in a location that could interfere with the driver's visibility, operation of vehicle controls, or on or near airbag panels or within the working range of an airbag.
Do not install this hardware on or near flammable or otherwise hazardous materials. This hardware may burst if placed near flammable or other hazardous materials, creating a risk of fire, burn, shock, or other serious injury.
This product includes capacitors, which may present a potential fire, explosion, electric shock, or burn hazard. Do not touch any capacitors within this hardware.
Please always pay attention to your surroundings and drive safely, comply with all traffic laws, and observe the road and driving conditions at all times. Do not rely on the product to alert the driver of safety hazards or to prevent collisions. The hardware and associated software may not work as intended depending on road conditions, other vehicles, weather, and other factors.
Hardware may sustain water damage if the seal is damaged. Do not use it if the seal appears damaged.
Keep this hardware between -31°F and 167°F (-45°C and 75°C). Failure to keep this hardware in the specified temperature range may result in safety risks.
Failure to follow mounting instructions may create risk of physical injury or property damage from falling objects. If mounting the hardware to a building wall, check for wiring or plumbing before drilling any holes.
Consult local housing ordinances and safety regulations before connecting hardware to an outlet or existing electrical system. It is the user's responsibility to follow all applicable housing ordinances and regulations. Consult an electrician before connecting the hardware to an outlet or existing electrical system. Improper installation may present a risk of electrocution, shock, and other physical injury.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device complies with ISED Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
|
|
This symbol on the product(s) and / or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take this product(s) to designated collection points where it will be accepted free of charge. |
Comments
0 comments
Article is closed for comments.