Bird's Eye View uses the same four HW-MC41 fisheye cameras on every vehicle. Mount locations, calibration-mat placement, brackets, and vehicle position for calibration vary by body type. Whenever possible, mount each camera on a flat vertical surface using the built-in mount. When the body prevents that, use a 90° tilt bracket (ACC-MC41-TILT) on an angled or horizontal face, or a band clamp bracket (ACC-MC41-CLMP) on a pole or round bar. For mounting and calibration steps that apply to every install, see Bird's Eye View Installation and Calibration Guide. For how the in-cab view and detections work after install, see Bird's Eye View Overview.
Choose a vehicle category:
Don’t see your vehicle? Send photos of the front, sides, and rear to your Samsara account team so Samsara can review placement with you.
Camera, mat, and bracket placement for box trucks, vans, and buses. For mounting and calibration steps that apply to every install, see Bird's Eye View Installation and Calibration Guide.
|
Camera Position |
Camera Placement |
Recommended Mounting Bracket |
|
|---|---|---|---|
|
|
Front |
Centered and as far forward as possible, facing forward |
None on a vertical surface; ACC-MC41-TILT on an angled or horizontal surface (for example, a roof) |
|
|
Left and right |
On the side of the box or van body, roughly halfway along, as high as practical |
None |
|
|
Rear |
Centered above the rear door |
None |
Mount one HW-MC41 fisheye camera on each side of the vehicle, roughly halfway along the body. Center the front camera and place it as far forward as possible, facing forward. The farther back you set the front camera, the more of the hood the top-down view displays.
Place the four calibration mats about 5 ft (1.5 m) from each corner of the vehicle so each camera sees two mats with no obstructions. Mount cameras on a flat vertical surface when possible. If the body prevents direct mounting, use a 90° tilt bracket or band clamp bracket, as described in Bird's Eye View Installation and Calibration Guide. When the body design allows, mount the left and right cameras at the same height and the same distance from the front of the vehicle. Calibrate on flat, level ground after you mock-mount the cameras, and again after permanent mounting.
Calibration position: Close the doors and liftgate.
Good calibration: The preview screenshot in the calibration steps of Bird's Eye View Installation and Calibration Guide shows what to expect. The dark rectangle in the middle is the vehicle you are calibrating. The other van at the edge is parked nearby.
Camera, mat, and bracket placement for common refuse truck body types. For mounting and calibration steps that apply to every install, see Bird's Eye View Installation and Calibration Guide.
|
Camera Position |
Camera Placement |
Recommended Mounting Bracket |
|
|---|---|---|---|
|
|
Front |
Varies by truck, however, typically mounted between or below the crush bars on the front of the vehicle (if applicable). |
ACC-MC41-TILT or ACC-MC41-CLMP, depending on the truck |
|
|
Left and right |
About 90 in. (2.3 m) above the ground on each side |
None |
|
|
Rear |
On or just above the tailgate, on a 90° tilt bracket or mounted upside down. If upside down, tap Flip for this view in the camera setup steps in Bird's Eye View Installation and Calibration Guide. |
ACC-MC41-TILT, or none |
Mount one HW-MC41 fisheye camera on each side of the truck. Keep the cameras and cables clear of the loader arms, forks, and other moving equipment through their full range of motion. Place the four calibration mats about 5 ft (1.5 m) from each corner so each camera sees two mats. Use screw mounting, a 90° tilt bracket, or a band clamp bracket for the body and any poles or cages. Calibrate on flat, level ground.
Calibration position: Stow the forks and close the tailgate.
|
Camera Position |
Camera Placement |
Recommended Mounting Bracket |
|
|---|---|---|---|
|
|
Front |
Varies by truckby truck, however, typically mounted between or below the crush bars on the front of the vehicle (if applicable). |
ACC-MC41-TILT or ACC-MC41-CLMP, depending on the truck |
|
|
Left and right |
Anywhere from halfway up to the top of the side (a higher position provides a better view), clear of the arm and any door that opens with it |
None |
|
|
Rear |
On or just above the tailgate, on a 90° tilt bracket or mounted upside down. If upside down, tap Flip for this view in the camera setup steps in Bird's Eye View Installation and Calibration Guide. |
ACC-MC41-TILT, or none |
Mount one HW-MC41 fisheye camera on each side of the truck. Keep the cameras clear of the side-loader arm and hopper equipment through their full range of motion. Place the four calibration mats about 5 ft (1.5 m) from each corner so each camera sees two mats. Use screw mounting, a 90° tilt bracket, or a band clamp bracket. Calibrate on flat, level ground.
Calibration position: Stow the arm and close the tailgate.
Good calibration: If the arm extends past the side where the camera sits, part of it displays in the view. This is expected.
Camera, mat, and bracket placement for rear-discharge concrete mixers. For mounting and calibration steps that apply to every install, see Bird's Eye View Installation and Calibration Guide.
|
Camera Position |
Camera Placement |
Recommended Mounting Bracket |
|
|---|---|---|---|
|
|
Front |
Centered at the top of the cab, for maximum forward coverage |
ACC-MC41-CLMP, if needed |
|
|
Left and right |
Centered on each side, raised about 2 ft (0.6 m) above the fender ledge on a riser |
Custom riser, built by your team or a fabricator with guidance from your Samsara account team (not supplied by Samsara) |
|
|
Rear |
Above the chute. As far away from the chute as possible. |
ACC-MC41-TILT |
Use these positions when you install risers.
Mount one HW-MC41 fisheye camera on each side of the mixer, away from the rotating drum. The discharge chute can permanently block part of the rear view. Use screw mounting, or a custom or 90° tilt bracket when no flat vertical surface is available. Calibrate on flat, level ground, and allow extra time to place mats on long vehicles.
The wheel fenders sit too low for a clean top-down view, so Samsara recommends raising the side cameras on risers. Place the four calibration mats about 5 ft (1.5 m) from each corner, and move the rear mats farther out to clear the chute. Each camera must still see two mats.
Calibration position: Stow the chute.
Protect the rear camera: Consider having your fabricator add a metal splash plate above it (Samsara doesn’t supply one). Fit the plate before you mount the camera. Mounting the camera higher and farther from the chute also helps protect it.
Caution
If anyone welds near installed hardware, disconnect the battery and unplug the camera first.
If you can’t install risers, you can use the following layout instead. Bird’s Eye View then has more distortion and artifacts. Place the calibration mats the same way.
|
Camera Position |
Camera Placement |
Recommended Mounting Bracket |
|
|---|---|---|---|
|
|
Front |
Top of the cab, ideally on the front bar so the bar does not block the view |
ACC-MC41-CLMP |
|
|
Left and right |
On the cab roof or on the mirrors using a CLMP bracket |
ACC-MC41-TILT or ACC-MC41-CLMP |
|
|
Rear |
On the rear frame, above the chute |
None |
Camera, mat, and bracket placement for wheel loaders, skid steers, excavators, and bulldozers. For mounting and calibration steps that apply to every install, see Bird's Eye View Installation and Calibration Guide.
|
Camera Position |
Camera Placement |
Recommended Mounting Bracket |
|
|---|---|---|---|
|
|
Front |
Top of the cab, ideally on the front bar so the camera does not block the view |
ACC-MC41-CLMP |
|
|
Left and right |
On the side railing outside the cab. Mounting on the cab directly typically leave to view obstructions due to the railing. |
ACC-MC41-CLMP |
|
|
Rear |
Directly on the upper rear grille |
None |
Mount one HW-MC41 fisheye camera on each side of the loader. Choose positions that stay stable as the machine articulates and keep the ground around the loader in view, with no blockage from the bucket, lift arms, tires, mirrors, or body panels. Use screw mounting, a 90° tilt bracket, or a band clamp bracket for the body geometry. Calibrate on flat, level ground.
Calibration mats: Place the front mats just in front of the cab, closer in than usual, where the front camera sees them clearly. Place the rear mats about 5–10 ft (1.5–3 m) out from the rear corners.
Calibration position: Keep the machine straight, not turned at the center joint, with the bucket on the ground.
Good calibration: The front of the loader displays in the view. This is expected.
Note
Bird's Eye View does not support articulating tractor-trailers. For wheel loaders and similar equipment, place cameras on parts of the machine that stay fixed relative to each other during articulation whenever possible.
|
Camera Position |
Camera Placement |
Recommended Mounting Bracket |
|
|---|---|---|---|
|
|
Front |
Upside down, under the top ledge. Tap Flip for this view during the camera setup steps in Bird's Eye View Installation and Calibration Guide. |
None for most models; ACC-MC41-TILT on some models |
|
|
Left and right |
Directly on the side of the machine |
None |
|
|
Rear |
Directly on the rear grille |
None |
Mount one HW-MC41 fisheye camera on each side of the skid steer. Choose locations that show the ground near the machine and stay clear of the lift arms, bucket, and cage through their full range of motion. Place the four calibration mats about 5 ft (1.5 m) from each corner so each camera sees two mats. Compact bodies often need a 90° tilt or band clamp bracket. Calibrate on flat, level ground.
Calibration position: Lower the lift arms and set the bucket on the ground.
|
Camera Position |
Camera Placement |
Recommended Mounting Bracket |
|
|---|---|---|---|
|
|
Front |
Toward the top of the cab. Before drilling, check that there are no wires or reinforcing plates behind the spot. If the cab itself is the ROPS/FOPS structure, don’t drill. Use a band clamp bracket on a rail. |
None, or ACC-MC41-CLMP on a rail |
|
|
Left |
High on the cab, clear of the door so the camera doesn’t get in its way |
None |
|
|
Right |
As high as possible on the side panel, on a surface parallel with the side of the machine. Route the cable through the engine bay to the pass-through at the back of the cab. |
None |
|
|
Rear |
At the top of the rear. Route the cable through the engine bay to the cab pass-through. |
None |
Mount one HW-MC41 fisheye camera on each side of the excavator house or on other fixed body surfaces. Avoid mounting only on the boom or stick, which move independently of the house. Place the four calibration mats about 5 ft (1.5 m) from each corner of the house footprint so each camera sees two mats. Use screw mounting, a 90° tilt bracket, or a band clamp bracket. Calibrate on flat, level ground.
Caution
While you place the calibration mats, raise the boom only enough to clear the front camera’s view and engage the hydraulic lockout. Keep everyone out from under the boom and bucket and outside the swing radius.
Calibration position: Line up the upper structure with the tracks and raise the boom. The cameras sit on the upper structure, so the view and zones turn with the cab when it swings.
|
Camera Position |
Camera Placement |
Recommended Mounting Bracket |
|
|---|---|---|---|
|
|
Front |
On the hand rails around the top of the cab, or directly on the cab if handrails aren't available. |
ACC-MC41-CLMP |
|
|
Left and right |
On the bars around the cab, if they run parallel with the side of the dozer |
ACC-MC41-CLMP, one per side |
|
|
Rear |
Directly on the panel near the top. Some models have an AC condenser here, so check before drilling. |
None |
Mount one HW-MC41 fisheye camera on each side of the dozer. Prioritize rugged mounting and protected cable routing, and place cameras so the blade doesn’t block the ground near the machine perimeter. Place the four calibration mats about 5 ft (1.5 m) from each corner so each camera sees two mats. Use screw mounting, a 90° tilt bracket, or a band clamp bracket. Calibrate on flat, level ground.
Calibration position: Lower the blade.
Good calibration: The view displays a good amount of the dozer itself. To include it in the vehicle outline, tap Adjust vehicle boundary during the calibration steps in Bird's Eye View Installation and Calibration Guide.
Comments
0 comments
Article is closed for comments.