Use this workflow to install the Vehicle Gateway (VG54 or VG55) with the accessory cable ACC-RS232.
What You Will Need
Quantity |
Description |
|
---|---|---|
|
1 |
Vehicle Gateway |
|
1 |
Accessory cable (varies by vehicle type) |
|
1 |
RS232 connector adapter |
|
2 |
RS232 connector standoffs |
|
2 |
Long-wide cable ties (cable bag) |
|
2 |
Short-narrow cable ties (cable bag) |
|
2 |
Long-narrow cable ties (VG box) |
|
1 |
Flush cutters (not provided) |
Connect the cable:
-
Ensure a Samsara Vehicle Gateway is already connected to the vehicle.
If a gateway is not already connected, install a gateway according to the vehicle-specific gateway power cable installation instructions.
-
Configure the serial-end of the ACC-RS232 accessory appropriately for your particular install:
You can optionally:
-
(A) Remove the screws and (B) install the included standoffs to allow mating to a serial connector with built-in screws.
-
(C) Attach the included null modem adapter to allow mating to a female serial connector.
-
-
Connect the USB on Samsara cable to the gateway.
Access the accessory device port by removing and properly discarding one of the port covers.
-
Attach the ACC-RS232 accessory serial-end to your serial port accessory.
For more guidance on specific RS-232 installation scenarios, see https://www.samsara.com/rs232.
-
If you experience any issues during installation, visit the Samsara Help Center to find solutions to most issues.
This installation guide contains typical information specific to products manufactured at the time of its publication. The contents of this guide do not constitute a warranty and are for reference only. Consult applicable local laws and ordinances to determine any installation restrictions. It is the installer’s responsibility to comply with all applicable laws and ordinances when installing this hardware.
Do not attempt to repair this product, use any third party replacement parts with this product, or otherwise modify this product except in accordance with product manuals or as otherwise instructed by Samsara. Failure to do so may cause property damage, lead to physical injury, or void your product warranty.
Any installation not in accordance with the instructions in the installation guide or otherwise in the Documentation or use of this product other than as described by the relevant IP rating or recommended operating instructions may result in unexpected downtime, system failure, physical injury, or property damage, including water damage. Failure to follow these directions could result in serious injury or death.
This hardware and any associated software may not be compatible with third party products and/or services and may interfere with the operations of or void warranties for such third party products and/or services.
Do not install hardware while the vehicle is unsecured or while the vehicle is turned on unless instructed to turn on the vehicle by the installation guide. Do not install or adjust hardware while driving or operating the vehicle. Do not install this hardware in a location that could interfere with the driver’s visibility or operation of vehicle controls or near airbag panels or within the working range of an airbag.
Do not install this hardware on or near flammable or otherwise hazardous materials. This hardware may burst if placed near flammable or other hazardous materials, creating a risk of fire, burn, shock, or other serious injury. This product includes capacitors, which may present a potential fire, explosion, electric shock, or burn hazard. Do not touch any capacitors within this hardware.
Please always pay attention to your surroundings and drive safely, comply with all traffic laws, and observe the road and driving conditions at all times. Do not rely on the product to alert the driver of safety hazards or to prevent collisions. The hardware and associated software may not work as intended depending on road conditions, other vehicles, weather, and other factors.
Keep this hardware between -40°C and 85°C (-40°F and 185°F). Failure to keep this hardware in the specified temperature range may result in safety risks.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
|
This symbol on the product(s) and / or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery, and recycling, please take this product(s) to designated collection points where it will be accepted free of charge. |
Comments
0 comments
Article is closed for comments.