This document provides a step-by-step guide for installing the CM33/CM34 Dash Cam Universal Mounting Bracket.
-
Gather the necessary equipment and tools.
Description
Vehicle Gateway (VG) (sold separately)
Dash cam (sold separately)
Diagnostic cable (varies by vehicle type, sold separately)
CM33/CM34 Dash Cam Universal Mounting Bracket
‘C’ cable clip
Adhesive clips (included with dash cam)
Allen key (included with dash cam)
-
If you have a previously installed dash cam, remove your existing equipment or follow our recommended steps to Remove an Installed Dash Cam.
-
Ensure your Vehicle Gateway (VG) is installed and activated, and activate your dash cam. Visit https://cloud.samsara.com/activate or follow the guided instructions in the Samsara Fleet App to complete activation.
Determine the appropriate mounting method for the universal bracket:
|
|
|
Examples of different mounting solutions
-
Identify a suitable mounting location:
-
Choose a horizontal and flat surface.
-
Avoid areas with black coating or dot patterns on the glass.
-
Ensure adequate clearance for Allen key access.
-
Position the device within the windshield wiper sweep. Refer to specific mounting tips for the US and UK.
-
Install the dash cam close to the windshield to avoid glare.
-
If utilizing AI event detection features, follow the dash cam position recommendations for AI Event Detection.
-
-
Install the bracket onto the substrate using #10 fasteners or pop rivets through the AMPS pattern holes.
The holes are specified for a #10 screw clearance fit.
If there is limited surface area, use the two additional holes on the mount to secure the mount to the substrate using #10 fasteners or pop rivets.
-
Proceed to Install the Dash Cam to the Universal Bracket.
|
|
|
|
Examples of different mounting solutions
-
Install the third-party mounting mechanism as per its instructions:
-
Choose a horizontal and flat surface.
-
Avoid areas with black coating or dot patterns on the glass.
-
Ensure adequate clearance for Allen key access.
-
Position the device within the windshield wiper sweep. Refer to specific mounting tips for the US and UK.
-
Install the dash cam close to the windshield to avoid glare.
-
If utilizing AI event detection features, follow the dash cam position recommendations for AI Event Detection.
-
-
Choose one of the following methods to fasten the universal bracket:
-
Align and secure the AMPS pattern to the third-party mount using screws.
Note
Some third-party mechanisms only use two of the four screws.
-
Fasten the brass ¼-20 insert to the threaded gimbal on the mount.
-
-
Proceed to Install the Dash Cam to the Universal Bracket.
-
Remove the existing mount on the dash cam and set aside the screws.
-
Lightly bend the universal mount arms to allow the dash cam to slide into the serrated tooth interface, and loosely tighten the captive screws (1-2 turns) to allow rotation and vertical adjustment. The screws are intended to stay attached to the universal mount.
Note
The dash cam should be able to rotate, and translate up and down, but no longer be removed from the bracket.
-
Adjust the dash cam to the desired height; checking that it’s vertical and right side up.
The cable should always be pointed upwards.
-
After the camera is oriented in the desired location, tighten the captive screws until snug.
Ensure that the installation torque does not exceed 1 N·m (8.85 lb·in).
-
If necessary for cable management, route the camera cable using the ‘C’ clip and then secure it to the bracket.
-
Connect the dash cam.
-
Run the cable across the top of the windshield.
Secure the cable with cable clips or tuck it under the windshield's glass seal, making sure the placement does not interfere with any vehicle safety systems, such as airbags.
-
Plug the camera into the USB port on the Vehicle Gateway.
For best results, do not wrap the cable around the Vehicle Gateway or route across the diagnostics cable.
-
-
Complete the installation.
-
Turn the vehicle on.
-
Verify installation:
-
Samsara dashboard: See Test Dash Cam Positioning
-
Samsara Fleet App: See Streamline Hardware Installation with the Samsara Fleet App
If all points of interest are not captured (see the following example), use the provided Allen key to loosen the camera before re-adjusting. After all points of interest are captured, use the Allen keys to tighten both mount locking screws and, if applicable, the inward camera locking screw. Do not overtighten.
Note
You may need to take a short trip for the camera to begin recording. A trip is registered when the vehicle reaches 5 mph (8 km/h).
-
Have more questions? Report an Issue.
-
This installation guide contains typical information specific to products manufactured at the time of its publication. The contents of this guide do not constitute a warranty and are for reference only. Consult applicable local laws and ordinances to determine any installation restrictions. It is the installer’s responsibility to comply with all applicable laws, and ordinances and rights to privacy in your jurisdiction when installing this hardware.
Do not attempt to repair this product, use any third party replacement parts with this product, or otherwise modify this product, except in accordance with product manuals or as otherwise instructed by Samsara. Failure to do so may cause property damage, lead to physical injury, or void your product warranty.
Any installation not in accordance with the instructions in the installation guide or otherwise in the Documentation or use of this product other than as described by the relevant IP rating or recommended operating conditions may result in unexpected downtime, system failure, physical injury or property damage, including water damage. Failure to follow these directions could result in serious injury or death.
This hardware and any associated software may not be compatible with third-party products and/or services and may interfere with the operations of or void warranties for such third party products and/or services.
Do not install or adjust hardware while driving or operating the vehicle. Do not install this hardware in a location that could interfere with the driver’s visibility, operation of vehicle controls, or on or near airbag panels or within the working range of an airbag.
Please always pay attention to your surroundings and drive safely, comply with all traffic laws, and observe the road and driving conditions at all times. Do not rely on the product to alert the driver of safety hazards or to prevent collisions. The hardware and associated software may not work as intended depending on road conditions, other vehicles, weather, and other factors.
Comments
0 comments
Article is closed for comments.